New

Pets

Pet Feeder Station

  like (0) I made it (0) Email Print
VIEW ALL Pets

STEPS

10

SKILL LEVEL

Dress up mealtime with this upcycled feeding station project. We'll show you tips on how we transformed an old dresser into a storage station that also keeps eating areas nice and tidy. Of course, your dimensions will depend on your dresser as well as the bowls you'd like to use.

by Dremel ®

228 PROJECTS

Tags

woodworking

Grid View List View

Supplies Needed For This Project

TOOL

SM20 Saw-Max Tool Kit

Model # SM20

TOOL

Multi-Max™ MM20

Model # MM20

TOOL

3000 Variable Speed Rotary Tool

Model # 3000

ACCESSORY

SM600 3" Wood & Plastic Flush Cut Wheel

Model # SM600

ACCESSORY

SM500 Wood & Plastic Carbide Wheel

Model # SM500

ACCESSORY

SM840 Saw-Max™ Miter Guide

Model # SM840

ACCESSORY

Dremel MM480 Wood Flush Cutting Oscillating Blade

Model # MM480

ACCESSORY

561 MultiPurpose Cutting Bit

Model # 561

ACCESSORY

678-01 Circle Cutter & Straight Edge Guide

Model # 678-01

Tools & Accessories

Materials

  • 1

    Dremel 150 1/8" Drill Bit

  • 1

    New or used dresser

  • 2

    Hinges

  • 1

    Drill

  • 1

    1" screws

  • 1

    Small sheet of melamine material

  • 1

    Pet food &/ or water dish with lip

Let's Get Started

To reduce the risk of injury user must read instruction manuals for all tools used in this project. Wear eye and respiratory protection. Use clamps to support work piece whenever practical.

STEP 1

Step 1

The first step we took for our dresser is to cut the dowel pins that secured the top of the cabinet. You might find that this is required for your dresser as well. To do this, we used our Multi-Max MM20 tool equipped with the MM480 Wood Flush Cutting Blade. With your tool set to a medium to high speed make a plunge cut between the dresser top and face panel to sever each dowel pin. Once complete, remove the top and set aside to use later. Before moving onto step 2, remove & reserve the drawer fronts to attach to future cleats for false front.

STEP 2

Step 2

Next, secure the top you just removed to your work bench and using the Saw-Max equipped with the SM500 Wheel, cut a 2.5" strip from the back edge. From a fresh piece of melamine, cut an inner shelf you'll later secure inside of your dresser. Measure the interior dimensions of your dresser and mark your material to that size. Cut along your marked lines. At this step, you'll need to cut another piece of material to the interior dimensions of your lower drawer, then cut that piece in half. These two pieces will hold the food & water dishes into the drawer once the project is complete.

STEP 3

Step 3

Before you begin securing the newly cut pieces into place, you'll need to create a series of cleats. We marked a series of 1" cleats on extra 3/4" plywood we had on hand. Using the Saw-Max equipped with the same SM500 Wheel, cut along the marked lines.

STEP 4

Step 4

Using your Saw-Max tool & SM500 blade, cut the cleats & drawer divider to size per the measured lengths for your dresser. You'll need the following : • (A) 1 for top hinge support • (B) 2 for false drawer front attachment • (C) 2 for rear panel support • (D) 2 for inner shelf support If desired, you may want to pull out your handy Dremel 3000 tool equipped with the 150 Drill Bit to make a series of pilot holes in your cleats before you secure them into place.

STEP 5

Step 5

Now that your cleats are ready, you'll first use them to attach your inner shelf. Determine the height you want your inner shelf to sit at. We sat our shelf far enough down from the top of the dresser so we could place a large bag of dog food inside. Secure one cleat along each side of the dresser using a drill and 1" wood screws.

STEP 6

Step 6

Finally, attach the remaining cleats as shown here. • (A) 1 for top hinge support • (B) 2 for false drawer front attachment • (C) 2 for rear panel support • (D) 2 for inner shelf support

STEP 7

Step 7

Secure the drawer fronts you reserved to the front panel cleats.

STEP 8

Step 8

Next, secure the 2.5" strip you cut in step 2 across the top, back of the dresser through the top, back cleat. Fasten the strip to the top of the dresser you reserved from step 2 with 2 hinges.

STEP 9

Step 9

Next, measure and mark the circular cuts you'll need to make for your lower bowl drawer. Mark lower drawer pieces you cut in step two 1/2" smaller than the diameter of your pet’s food & water dishes. This will allow the bowls to recess into your drawer & will hold them securely into place. We used the 561 bit, mounted the Circle Cutter onto our tool, set the diameter to the appropriate length and began cutting at full speed. Cut in a clockwise direction using consistent, moderate pressure. Depending on your dresser's design you may be able to simply lay the two pieces onto the top of the drawer or secure them with 1-2 screws. TIP: To assemble the cutter, unscrew the pivot foot knob and turn the picot foot over so that the center point is down. Next, remove the nosecap of the 3000 tool then thread the Guide onto the threaded portion of the tool, turning clockwise until tight (do not over-tighten).

STEP 10

Step 10

For an added decorative touch, we miter cut & secured molding across the bottom of our cabinet. To complete a miter cut using your Saw-Max tool: 1. Measure and mark the desired cut line on the trim. 2. Position the Miter Guide over the wood in the designated location of the cut. 3. Clamp the cutting guide to the workpiece in the desired location to make the cut. 4. Firmly hold the tool and make the cut.

VIEW ALL STEPS SHOW LESS STEPS

Suggested Videos

VIEW ALL VIDEOS

Saw - DIY

How to Replace Damaged Plywood Subfloor

800

Rotary Tool - Demo

EZ Twist Demo

7921

Rotary Tool - Demo

EZ-Lock Accessories

6479

Saw - DIY

How To Install a Vent Cover

477

VIEW ALL VIDEOS

Other Projects You Might Like

VIEW ALL PROJECTS
Bean Bag Toss Game
games
Bean Bag Toss Game

3years ago

Make a Street Address Sign
home decor
Make a Street Address Sign

9months ago

Birch Wood Candle Holders
home decor
Birch Wood Candle Holders

3years ago

Wooden Beer Caddy
woodworking
Wooden Beer Caddy

3years ago

VIEW ALL PROJECTS
No Promotion available!

SHOW US WHAT YOU MADE

Send us a photo of your Dremel creation so we can share it with the world.

Submit A Project
No Promotion available!

TOUR THE MAKER GALLERY

Explore the creations added to the Maker Gallery by Dremel Makers.

View Gallery

Comments(0)

Sign In to post comments on this project.

No comments yet.

No Promotion available!

Dremel Experts

From drilling holes to distressing denim, Dremel’s Customer Service has an answer.

SUPPORT