New

Craft and Hobby

String Art

  like (0) I made it (0) Email Print
VIEW ALL Craft and Hobby

STEPS

10

SKILL LEVEL intermediate

Beginner Intermediate Advanced
Perfect for a Valentine’s Day Gift, Wedding Gift or every day decor, commemorate important places to you with this modern twist on old-fashioned string art!

by Dremel ®

231 PROJECTS

Tags

Grid View List View

Supplies Needed For This Project

TOOL

SM20 Saw-Max Tool Kit

Model # SM20

TOOL

Dremel Moto-Saw™

Model # MS20

TOOL

3000 Variable Speed Rotary Tool

Model # 3000

ACCESSORY

SM500 Wood & Plastic Carbide Wheel

Model # SM500

ACCESSORY

MS51 Wood & Plastic Cutting Blade

Model # MS51

ACCESSORY

EZ Drum™ Mandrel

Model # EZ407SA

Tools & Accessories

Materials

  • 1

    Sheet of 3/8” Plywood

  • 1

    Sheet of 3/8” Plywood

  • 1

    1 ½” Finishing Nails

  • 1

    Hammer

  • 1

    Wood Glue

  • 1

    Screwdriver

  • 100

    1” wood screws

  • 1

    Craft string/floss

Let's Get Started

To reduce the risk of injury user must read instruction manuals for all tools used in this project. Wear eye and respiratory protection. Use clamps to support work piece whenever practical.

STEP 1

Step 1

Measure and mark your ¼ inch plywood to the desired dimensions for the state. Cut your 1/4 inch plywood to size using the Saw-Max and SM500 Wood and Plastic Wheel. If you are mounting a heart to your piece we recommend cutting a small mounting block at this stage as well. We cut ours to 1 X 2 inches as our heart is 3 inches wide.

STEP 2

Step 2

Using your Moto-Saw and the MS51 Wood and Plastic Wheel, cut along your state pattern. You may find it easier to clamp your plywood to your workbench and cut the state piece using the Moto-Saw in the hand-held position for this application. If desired cut your heart shape using the same technique. However, we recommend the table top position and spray mounting patterns for smaller cut-outs. Run your tool at a speed setting of 6 for this application. Remember to let the speed of the tool do the work and do not force the blade through the plywood.

STEP 3

Step 3

While your Moto-Saw is still set up, this is a good time to cut your heart shape. We found it easiest to size our heart on the computer & print off the shape. Then we spray-mounted the paper onto our ¼” MDF & using the same technique as in step 2, trace along the heart outline.

STEP 4

Step 4

If desired, sand the edges of the your pieces using your favorite Dremel Rotary Tool and a EZ407SA sanding band. Install your accessory into the tool, set the tool to a medium to high speed and lightly trace along the edge of the shape. We found it easiest to hold our tool perpendicular to the side of the shape to allow the drum to sand along the entire edge of the shape evenly.

STEP 5

Step 5

Next, using your Dremel Saw-Max equipped with the SM500 Wood & Plastic Blade, cut a mounting square slightly smaller than the width of the heart & secure to the back of the heart. This will come in handy in the last step of the project, helping set the heart up, off of the state.

STEP 6

Step 6

Paint the pieces your desired colors and allow them to dry completely.

STEP 7

Step 7

Next, choose where you would like to place your heart. We located our heart in Racine, Wisconsin where the Dremel Brand was originally founded & where you can still contact us at Customer Service today! Wherever your heart is, trace along the outer edge and set the wooden heart aside.

STEP 8

Step 8

This is the lengthiest step in the project- adding the nails! Set nails every 2 inches apart along the border of your state. Then, set more tightly-placed nails along the outline of the heart you traced in step 7. Test to ensure your nails are securely in place by pulling up on a few nails with your fingers. If they slip out of place, you’ll either need to sink them in deeper or use wood glue for an extra-secure fit.

STEP 9

Step 9

Now is the fun part! Begin by tying a knot on the outermost nail in your heart pattern. Next, run your thread up to the nearest nail along the border & loop the thread around the nail. Run the thread back down to the next nail on the heart & repeat. You may like your string pattern to be more hap-hazard than our starburst shape, in which case, loop the string around random nails along the border! We used hemp thread from the craft store and wrapped it taught around our nails. At this step you may want to employ an extra set of hands to keep the string in place during the stringing process!

STEP 10

Step 10

Finally, mount your heart over the nail outline. The heart will cap off the nails for a finished look. Once placed, secure your heart into place from the back of your piece using a drill & fasten picture hanging wire on the back.

VIEW ALL STEPS SHOW LESS STEPS

Suggested Videos

VIEW ALL VIDEOS

Saw - DIY

How to Replace Damaged Plywood Subfloor

800

Rotary Tool - Demo

EZ Twist Demo

7921

Rotary Tool - Demo

EZ-Lock Accessories

6479

Saw - DIY

How To Install a Vent Cover

477

VIEW ALL VIDEOS

Other Projects You Might Like

VIEW ALL PROJECTS
Upcycled Window Table
furniture
Upcycled Window Table

2years ago

Light-up Headboard
furniture
Light-up Headboard

3years ago

Custom Headboard
home decor
Custom Headboard

3years ago

Tape Dispenser
organizational
Tape Dispenser

11months ago

VIEW ALL PROJECTS
No Promotion available!

TOUR THE MAKER GALLERY

Explore the creations added to the Maker Gallery by Dremel Makers.

View Gallery
No Promotion available!

SHOW US WHAT YOU MADE

Send us a photo of your Dremel creation so we can share it with the world.

Submit A Project

Comments(0)

Sign In to post comments on this project.

No comments yet.

No Promotion available!

Dremel Experts

From drilling holes to distressing denim, Dremel’s Customer Service has an answer.

SUPPORT